Home » Sewing » Wrap Bracelet – Ta-dah & a tutorial!

Wrap Bracelet – Ta-dah & a tutorial!

Back last week (I think, time goes by so quickly sometimes!) the sun was shining and I was suddenly presented with An Opportunity –  Littlest Boy had fallen asleep (and stayed asleep despite the transfer from car to bed) and the other two Littlies were at school/nursery; and The Inspiration –  I’d had an idea a while back for a bracelet and after reading some blog posts about the Liberty Scrap Challenge I was suddenly struck with an idea of how to use some Liberty of London fabrics that I had lying around. I seized the time to try it out!

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

I’m so pleased with how the wrap bracelet came out and have been wearing it nearly every day since. I’m even thinking of making one out of one strip of fabric with maybe some fancy stitching down each side to jazz it up.

Would you like to see how I made it??? You will need;


  • A tape measure
  • Scraps of fabric 2″ wide
  • A length of interfacing 2″ wide
  • Some ribbon/ric-rac
  • A toggle & clasp
  • Contrasting/Complementary/Matching thread

Make the Fabric Wrap Bracelet

1. First off, you’ll need to measure your wrist, and then decide how many times you would like the bracelet to wrap around your wrist (my wrist is 6.25″ and I wanted 3 wraps which gave me a total length of 18.75″).

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

Tip: the looseness in this bracelet comes from the length of the toggle clasp & ric-rac. I have found that the bracelet does stretch with wear and found it to be a perfect fit for me but if you like looser bracelets then you might want to add on a bit of extra length

I was looking to use some Liberty of London scraps (this seems such a derogatory term for such beautiful fabrics!) that I’ve been saving. I’d cut 5 different lengths of fabric and allowed a 1/4″seam for each join as well as a 1/2″ fold over at each end), so had a total length of 21.75″ pre-sewing. Alternatively, you could just sew lots of strips of fabric together and trim to size!

2. Sew all your pieces together and give it a good press. I pressed my seams open as I wanted the bracelet to be as smooth as possible.

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

3. Iron interfacing on to the wrong side of the fabric to give it a bit of extra weight and strength – this may not be necessary depending on the fabric that you’re using. At this point, I also folded the entire length of the bracelet in half and then each edge into the middle – much as you would with bias binding – and gave it a good press.

4. Back at the sewing machine, I chose to do some decorative stitching between each fabric join. I thought this would help to tie each of the fabrics together and give me a chance to use some of the machine stitches that I don’t often use!

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

5. I’m using a toggle and clasp at each end and attached these using some ric-rac that I had lying around. I used some fray check to stop it fraying too badly. It is a little bit of a fiddle to get the toggle onto the ric-rac – there’s a fair bit of wriggling and pulling but I got there eventually! You could easily use ribbon or small scraps of fabric instead.

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

6. Fold over the ends of your bracelet by about 1/2″, position your toggle/clasp into one of the outside quarters (as marked by your iron creased lines!) and stitch into place. I used a sewing machine but it could easily be done by hand. Although not necessary, I found it really tricky to keep them in the right position whilst sewing around the perimeter without securing them beforehand.

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

7. Sew around the perimeter of your bracelet – I started near the top corner and adjusted my machine so that it was sewing on the furthest edge. When you reach each end of the bracelet very carefully sew across the bottom – I found it easier to do this manually as the layers of fabric are quite thick and you are so close to the edge it could easily get knarled in the machine. I also chose to do an extra line of stitching at each end. Overlap the beginning and end stitches to make sure that nothings going to start unravelling.

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

8. Put it on your wrist and enjoy!!!

Fabric Wrap Bracelet tutorial by fabricandflowers | Sonia Spence

I hope this all makes sense – it is my first tutorial so please let me know if anything could be made clearer.


  1. Melksham Mum
    June 11, 2012 / 9:35 pm

    I love this and I adore bracelets.mi am going to have a go at making this. Daft question… Where do I get the toggle and clasp bit from?! x

  2. June 11, 2012 / 9:58 pm

    Thanks Viv – let us know how you get on 🙂 x